
A new monitor can change how a PC feels overnight, and it can also expose a graphics card that was perfectly fine until then. The two upgrades in the title, 1440p and 144Hz, are often bought together, but they put very different demands on your hardware. One changes how many pixels your GPU has to draw, the other only changes how often the screen can show a new frame. Before spending money on either, it helps to know which one actually hits your GPU, how much it costs in frames per second (FPS), and what to check first.
Resolution and Refresh Rate Are Two Different Loads
A 1440p monitor (2560 × 1440) shows 3,686,400 pixels per frame, against 2,073,600 on a 1080p monitor. That is 78 percent more pixels for your GPU to shade, and it is the part of this upgrade that adds real work.
Refresh rate is a separate matter. A 144Hz panel can refresh up to 144 times per second, but it does not ask your GPU to produce 144 frames. If your GPU delivers 90 FPS, the monitor shows 90 frames per second; it never lowers your frame rate, it only limits how many frames you can see.
Pixel count alone does not give the FPS loss either. If every part of rendering scaled with pixels, a game running at 60 FPS at 1080p would drop to about 34 FPS at 1440p, but real games do not behave that way, since some of the work depends on geometry, physics, AI or the engine rather than on resolution.

What Upgrading to 1440p Actually Costs in FPS
The most useful public numbers come from the GPU benchmark hierarchy at Tom’s Hardware. As of its June 2026 update, it tests every card on a Ryzen 7 9800X3D across 11 games, at a mix of high and ultra settings depending on the game, with upscaling and frame generation off. The table shows average FPS at 1080p and 1440p for a few cards from that list, with the drop between the two calculated from the published averages.
| Graphics Card | 1080p Average | 1440p Average | Drop |
|---|---|---|---|
| GeForce RTX 5070 Ti | 155.4 FPS | 116.8 FPS | About 25% |
| Radeon RX 9070 XT | 156.6 FPS | 116.5 FPS | About 26% |
| GeForce RTX 5070 | 132.6 FPS | 96.4 FPS | About 27% |
| GeForce RTX 5060 Ti 16GB | 105.2 FPS | 73.4 FPS | About 30% |
| GeForce RTX 5060 | 88.5 FPS | 59.8 FPS | About 32% |
| GeForce RTX 4060 | 71.5 FPS | 47.6 FPS | About 33% |
| GeForce RTX 3060 (12GB) | 61.5 FPS | 41.9 FPS | About 32% |
The real drop is far smaller than the 78 percent pixel increase, between roughly a quarter and a third of the frame rate for these cards, and the faster cards lose a little less than the entry-level ones, which lose about a third. These are averages across 11 games, not a promise for the game you play: a competitive shooter and a heavy open-world game will not lose the same amount, so read the last column as a typical range.
On 144Hz, an average of 144 FPS at 1440p is only reached or approached at the very top of the list, where the RTX 5090 averages 167.3 FPS and the RTX 4090 averages 143.4 FPS. The seven cards above land between about 42 and 117 FPS at 1440p, so hitting 144 FPS usually means lowering settings in demanding games. A 144Hz monitor is still not a waste, as the variable refresh rate section below explains.
Check Your CPU Before Blaming the GPU
A low frame rate after a monitor upgrade does not always point to the GPU. Tom’s Hardware published a test of CPU scaling with DLSS in February 2026, using an RTX 4080 Super with four processors. At 1440p, the Core i5-14400 was a complete bottleneck, while the Ryzen 5 9600X was close to one. At 1080p, every chip except the Ryzen 7 9850X3D was completely CPU-bound. The full test shows the effect varies by game, so it is a warning rather than a verdict on any processor.
The article also suggests a simple check: compare your FPS in DLSS Quality mode with Performance mode, and if the numbers are identical, the CPU is holding the frame rate back and a faster graphics card will not help. Our CPU and GPU bottleneck guide explains how to tell the two apart.
VRAM: Where 8 GB Starts to Struggle at 1440p
Resolution itself adds relatively little video memory. In TechSpot’s VRAM testing, Ratchet & Clank: Rift Apart used about 7 percent more memory at 1440p than at 1080p, while quality settings, ray tracing and frame generation push usage up further. The same testing shows how much depends on the game:
| Game and Setting | VRAM at 1440p | Fits in 8 GB? |
|---|---|---|
| Cyberpunk 2077, Ultra, no ray tracing | Within 8 GB | Yes |
| Cyberpunk 2077, ray tracing | 12 GB | No |
| Alan Wake 2, ray tracing | 12 GB | No |
| Avatar: Frontiers of Pandora, Ultra | 12.6 GB | No |
| Starfield | Low usage | Yes |
TechSpot’s conclusion is that 8 GB is inadequate for higher-end gaming, especially at 1440p with high-quality settings or ray tracing, and that 12 GB should be the bare minimum, with 16 GB as the ideal target for ray tracing. Frame generation pushes usage higher still: in Cyberpunk 2077 with ray tracing and frame generation, the same testing measured about 13.5 GB at 1440p. These figures were measured on an RTX 4090, so they show how much memory each game uses, not what a smaller card will do. If you own an 8 GB card, expect to lower texture quality or skip ray tracing in some recent games at 1440p, and check your own games before concluding anything.
Get the Monitor Settings Right
Before blaming the hardware, check these settings.
Set the Refresh Rate in Windows
Do not assume Windows picked the highest refresh rate for you. Open Start, then Settings, System, Display, and Advanced display, and choose the rate under “Choose a refresh rate.” Microsoft notes that rates marked with an asterisk do not support your current resolution, and selecting one changes the resolution, so read the options carefully before picking. The steps are on Microsoft’s support page.
Turn On Variable Refresh Rate and Cap Your FPS
With variable refresh rate (VRR), whether G-Sync or FreeSync, the monitor adjusts its refresh rate to match your frame rate. Blur Busters explains the difference with traditional V-Sync: when a frame misses its refresh window, V-Sync locks the frame rate to half the refresh rate, while G-Sync adjusts the refresh rate to the frame rate in that same moment. A 144Hz monitor with VRR therefore stays useful when your GPU only reaches 90 or 100 FPS, since you get smooth motion without needing to hit 144.
Blur Busters and TechRadar both also recommend limiting your frame rate slightly below the monitor’s maximum refresh rate, so the game stays inside the VRR range. Our guide on fixing low FPS in games shows a typical G-Sync setup.
Use the Right Cable and Port
Use DisplayPort when your monitor and GPU both have it, and start with the cable that came in the box. The exact cable and port requirements depend on the monitor, so check its manual before assuming that every DisplayPort or HDMI port supports 1440p at 144Hz. Then confirm the result in Windows rather than assuming it.
Frame Generation Is Not a Replacement for Real FPS
Frame generation can make a game look smoother on a high refresh rate monitor, but it works best on a frame rate that is already decent. AMD says FSR Frame Generation works best from a base frame rate of at least 60 FPS, and Intel lists 40 FPS as the minimum for XeSS Frame Generation while still recommending 60.
Latency is the reason. In a Tom’s Hardware test with an RTX 5070 in Cyberpunk 2077, at a 4K target with DLSS Ultra Performance and path tracing, input latency was 35.0 ms with multi-frame generation off, 46.6 ms at 2X and 53.2 ms at 4X. It is a demanding test and results at 1440p will differ, but the frame counter goes up and so does the delay between your mouse and the screen.
Frame generation is better seen as a way to make use of a high refresh rate monitor than as a fix for a GPU that is too slow, and our guide to setting up DLSS 4 and frame generation covers how to use it.
When Your GPU Really Should Change
Changing the GPU makes sense when the problem is the GPU, and you can check that before buying anything. These are the cases where it usually is:
- Your FPS at 1440p stays below the level you want after you have lowered settings and tried an upscaler.
- Your card runs out of video memory in the games you play, which shows up as texture problems or stutter after raising quality settings.
- Your FPS rises clearly when you lower the render resolution, which means the GPU was the limit.
If none of that applies, a monitor upgrade may be all you need. If you do decide the GPU has to go, which card to buy and at what price is covered in our guide to upgrading your GPU in 2026.
A Simple Test Plan Before You Buy the Monitor
You can estimate how your current setup will behave at 1440p without owning the monitor.

- Note your average FPS in the games you play most, at your current resolution and settings.
- Raise the render resolution to 1440p if the game has a resolution scale slider. A scale of about 133 percent on a 1080p screen renders at roughly 1440p (1920 × 1.333 is about 2560).
- Play for a few minutes in a demanding scene and compare the new FPS to your first number.
- As a rule of thumb, watch your GPU and CPU usage while you play. A GPU running near its limit means it is the bottleneck, and a GPU well below its limit with a low FPS points to the CPU.
- If the FPS you get is acceptable, the upgrade should be fine. If not, you will have to choose between lower settings and replacing the card.
The Short Version
A 1440p monitor adds real work for your GPU, and a 144Hz refresh rate adds none by itself. Measured data from Tom’s Hardware shows a typical drop of roughly a quarter to a third of your FPS when moving from 1080p to 1440p, much less than the 78 percent pixel increase suggests.
- Check your CPU first, because a CPU limit will not be fixed by a new GPU.
- Check your VRAM, especially on 8 GB cards, with ray tracing and high texture settings.
- Set the refresh rate in Windows, turn on VRR and cap your FPS slightly below the maximum.
- Treat frame generation as a bonus on top of a decent base frame rate, not as a fix.
Frequently Asked Questions
Is a 144Hz Monitor Worth It if My GPU Only Reaches 100 FPS?
Yes, it can be. With variable refresh rate the monitor adjusts to your frame rate, so you still get smooth motion at 100 FPS. The 144Hz figure is a ceiling, not a requirement.
Does a Higher Refresh Rate Lower My FPS?
No. Your frame rate depends on your hardware and settings. The monitor’s refresh rate decides how many of those frames it can show, and what costs GPU performance is rendering more pixels per frame.
Can DLSS or FSR Let Me Keep My Old GPU at 1440p?
They can raise your frame rate in supported games, but they do not remove a CPU limit, and Tom’s Hardware found the CPU often limits performance at 1440p when DLSS is on. Test your own games before relying on an upscaler.

